Speedhut 2-1_16 inch, 2-5_8 inch, & 3-3_8 inch Revoluti User Manual download pdf

2-1/16”, 2-5/8”, and 3-3/8” Revolution/Legacy Gauge Instructions

Ground (black)

+12 volts Dash lighting (white)

(Yellow)

snap connector for dial lighting

Voltage gauge

12 volt

power source

(Black)

snap connector for dial lighting

Pressure gauges

(Black)

snap connector for dial lighting

Temperature gauges

1.Disconnect negative (-) Battery Cable

2.Connect wiring as above.

3.Mount Gauge for easy viewing. Use spin lock ring (included) to mount to panel. Spin ring

threads in both directions. Snap white gauge connector to wire harness.

4.Reconnect negative (-) battery cable.

1/8 npt threads

Ground (black)

+12

Ground (black)

+12

+12 volts Keyed ignition

(Red)

(Black)

Ground

(White)

+12 volts Dash lighting

Power distribution cable to plug all gauges into

+12 volts

(Red)

(Black)

Ground

(White)

+12

Power distribution cable to plug all gauges into

+12 volts

(Red)

(Black)

Ground

(White)

+12

Power distribution cable to plug all gauges into

Clock Gauge

+12 volts Battery voltage

Connect to contstant 12Volts

(Red)

(Black)

Ground

+12

Note: To adjust time use included 3.5mm jack plug

button.

1. plug into back of gauge.

2. press and hold button to rotate clock hands to

current time

Note: Tie both lighting white wires together

and both black ground wires together.

Note: Tie both lighting white wires together

and both black ground wires together.

Note: Tie both lighting white wires together

and both black ground wires together.

(Gauge Dial lighting)

(Main gauge power)

(Pointer (needle) lighting)

Note: Clock Hands do not glow at night

INVERTER

Keyed ignition

volts Dash lighting

volts Dash lighting (white)

will remain in last powered position.

Harness Wires:

White wire - Signal

Black wire - Ground

Harness Wires:

White wire - Signal

Black wire - Ground

Red wire - 5 volt reference

Power Draw = 0.2 Amp

5 Amp Inline Fuse Recommended

for +12 Keyed Ignition

Power Draw = 0.2 Amp

5 Amp Inline Fuse Recommended

for +12 Keyed Ignition

Inverter Note: INVERTER IS REQUIRED FOR GAUGE DIAL LIGHTING. E18-686-5CR is single

gauge inverter to light single gauge. C01-18N-2 and C11-18A01 are multiple gauge

lighting inverters that can light up to 6 - 8 gauges depending on inverter model.

See Inverter Note

Power Draw = 0.2 Amp

5 Amp Inline Fuse Recommended

for +12 Keyed Ignition

Trimable area

DO NOT trim pass the slot.

1 2

Summary of Contents

Page 1 - Pressure gauges

2-1/16”, 2-5/8”, and 3-3/8” Revolution/Legacy Gauge InstructionsGround (black)+12 volts Dash lighting (white)(Yellow)snap connector for dial lightingV

Page 2 - NO Peak Features

Setting warning LED for both low and high. LED can be set to turn on for both a low or high condition, or To reset LED set point at any time follow t

Comments to this Manuals

No comments

Speedhut 2-1_16 inch, 2-5_8 inch, & 3-3_8 inch Revoluti User Manual

Browse online or download User Manual for For the car Speedhut 2-1_16 inch, 2-5_8 inch, & 3-3_8 inch Revoluti. Speedhut 2-1_16 inch, 2-5_8 inch, & 3-3_8 inch Revolution_Legacy Gauge User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For the car Speedhut 2-1_16 inch, 2-5_8 inch, & 3-3_8 inch Revoluti