Speedhut 4 inch & 4-1_2 inch Dual GPS Speedometer_Fuel User Manual

Browse online or download User Manual for For the car Speedhut 4 inch & 4-1_2 inch Dual GPS Speedometer_Fuel . Speedhut 4 inch & 4-1_2 inch Dual GPS Speedometer_Fuel Level User Manual

  • Download
  • Add to my manuals
  • Print
  • Page
    / 3
  • Table of contents
  • BOOKMARKS
  • Rated. / 5. Based on customer reviews
Page view 0
Ground (black)
+12 volts Dash lighting (white)
Your speedometer has either a button on
front or plug in 3.5mm jack button on back for
programming and entering menu options
depending on speedometer model. If your
speedometer has a 3.5mm jack with plug in
button, mount button in convenient location for
easy menu adjustments.
Snap connection
for dial lighting
+12 Volts keyed ignition
(Red)
(Black)
Ground
(White)
+12 Volts Dash lighting
Power distribution cable to plug all gauges into
(green with yellow)
(green with red)
(blue with white)
**left turn signal +12V pulse
**right turn signal +12V pulse
**high beam wire +12V
Inverter
Note: Tie together the
+12volt dash lighting white
wire to the +12 volt inverter
white wire and connect to
the same dash lighting
source.
+12Volts Hot Start (Red with black)
+12 Volts constant power (low current)
1. Hook up speedometer power requirements as shown above.
2. Plug GPS receiver antenna into back of speedometer.
3. For best performance, mount GPS antenna with as much view of sky as possible (preferably on the roof of the vehicle). The GPS antenna is waterproof
and magnetic. If the car’s roof is not accessible then mount the antenna on top of the vehicle’s dash with as much exposure as possible to the sky through
the window. (Antenna is able to receive signal through some thin materials i.e. wood, glass, berglass, and plastic. All types of metal will block the signal.)
4. Hot start feature is optional. Hooking up the Hot start wire to constant +12volts allows GPS to quickly acquire satellites in less than 2 seconds.
This feature saves your current satellite position within the speedometer enabling it to quickly restore your position on power up when
to the satellites
The current draw is extremely low and will have virtually zero impact on a car batterys charge.
Hotsart wire should be connected directly to battery +12voltage and should remain powered 100% of the time.
GPS Antenna
(Black)
(white)
(black)
fuel sender output
fuel sender ground
Note: fuel sender ground is hooked
up to fuel level sensor ground.
If your sender does not have a
ground terminal, attach this wire to
chassis ground. THIS GROUND
WIRE MUST BE HOOKED UP TO
GROUND.
4-1/2" and 4" Dual GPS Fuel level / Speedometer Instructions
WARRANTY - Speedhut inc. warrants to the consumer for a period of 5 years from the date of purchase that the product will be free from defects in materials or workmanship.
Speedhut warrants to the consumer for a "LIFE-TIME" that the gauge circuit board will be free from defects in materials or workmanship. Please contact Speedhut service dept.
If you have a problem with this gauge. suppor[email protected]
INVERTER IS REQUIRED FOR GAUGE DIAL LIGHTING
(Pointer (needle) lighting)
(Main gauge power)
(Gauge Dial lighting)
Inverter Note: E18-686-5CR is single gauge inverter to light single gauge.
C01-18N-2 & C11-18A01 are multiple gauge lighting inverters that can light
up to 6 - 8 gauges depending on inverter model.
Power Draw = 0.2 Amp
5 Amp Inline Fuse Recommended
for +12 Keyed Ignition
Page view 0
1 2 3

Summary of Contents

Page 1 - Inverter

Ground (black)+12 volts Dash lighting (white)Your speedometer has either a button on front or plug in 3.5mm jack button on back for programming and en

Page 2 - 1/4 MILE

000000Menu Features - momentarily press button on speedometer to select dierent menu items. 000000MIMIOdometer (shows up to 999,999 miles or kmh Trip

Page 3 - Fuel level Setup menu

Fuel level Setup menu Note: This calibration can be done with sensor hooked up or NOT hooked up to gauge. If sensor is hooked up to gauge, gauge wil

Comments to this Manuals

No comments